1. VCI installation done in the T block

Updated files pasted in MRV DL3

1. All 11 DL3 integrated in the S block for trial purposes. 25 vehicles took trails on the vehicle level. All DL3s are working fine. Tomorrow we will deploy all 11 new DL3 in the S block

UB_TWO station DL3 checked from S block. There was facing network related issue.OFFLINE area DL3 checked from V block. There file not transfer to report logic. Issue corrected

1. DL3 3049 checked their battery issue, told to M&M2. All DL3 checked from S block

DL3 3048 checked from V block data, not uploading on report logic issue checkedDL3 from S block UB2 area checked DL3 3046 checked, it seems the shutdown condition needs to check whether their battery is ok or not

1. Toughbook from the T block had a runtime crash issue when VIN scan from the external scanner.2. Issue troubleshoot and corrected.3. DL3 3049 from V block have LED related issue was observed and sudden it's off4. DL3 repaired now its working fine

1. DL3 3058 repaired front panel and scanner replaced from DL3.

1. DL3 3032 WIFI card replaced 2. Tested online, working fine.3. ATP sign-off sheet sent to Mahindra4. Regarding new project discussed with Abhishek with Tushar

1. DL3 3032 - predominantly displayed a flashing PR message on the floating logo screen. 2. DL3 0108 - exhibited fluctuations in battery percentage and similarly showed a PR message on the floating logo screen. both DL3 checked and found the root cause

DL3 2203 LED have an issue; the DL3 LED repaired cable was inserted properly in the IPMB locking system.DL3 2300 LED have an issue; the DL3 LED repaired cable was inserted properly in the IPMB locking system.

DL3 3029 Scanning not happened issue checked, there is an issue with the scanner or front panel. Need to check and replace. 

- The Q7 board to be replaced from DL3 2048 to DL3 3054.- The Amphenol screw to be installed from DL3 2048 to DL3 3029. - The battery to be changed from DL3 2048 to DL3 3029.- The DL3 2205 Ethernet drivers installed

DL3 2246 battery board changed

1. T block FINAL_LINE_PC try to reinstall all the EOL related MAHLE drivers.2. Due to lack of admin rights i didn't reinstall all the driveres

1. New DL3 000102 configured for W616 project2. Testing done.

1. Regarding IQA details given to MRV team2. Co-ordinate with them related scanning procedure 3. Working fine

1 DL3 configuration procedure partially done.

1. DWVCI_2 checked issue "CONNECT CABLE"2. After checking found there is issue in OBD cable suggested to replace cable

WIFI card changed for DL3 2210

DL3 2049 WIFI card changed

1. DL3 2208 WIFI card troubleshooting2. Drivers uninstalled and reinstalled3. WIFI card changed mail sent to MAHINDRA team

1. DL3 2208 and DL3 2210 checked ZIG have a fuse issue,2. DL3 2208 WIFI card have issue

S block all DL3 details sent to Radhika.

1. FINAL_LINE DL3 checked and added auto negotiation to static negotiation commands.2. FINAL_LINE DL3 added PCAP file path.3. tested on vehicle level.

1. DL3 3050 taking too much time to send report in report logic2. Me and tushar checked key points3. FB rasied assign to US team

1. DL3 3050 Data reflect or not checked in report logic server

1. DL3 3050 configured. Tested on line.

1. DL3 3050 format done.2. Handover to IT team to get in mahindra domain

1. DL3 2208 Q7 board changed from DL3 2211. Tested working fine

1. DL3 3050 printer enabled and took trials on-line2. DL3 3377 WIFI driver installed, New firmware added, new runtime installed, new binary installed, network-related setup done. Took the trails on the vehicle level.

1. DL3 2203 WIFI card changed and tested.2. DL3 2299 WIFI card changed and tested.3. DL3 2433 Battery and battery board changed.

Tried to configure DL3 but due to IT issue. DL3 configuration incomplete.

1. I added services in WLC. 2. Also I added new model code in Z1. 3. Enabled EPS applicable model code in Z1.4.  Removed one EPS's applicable model code and added one not applicable model code in Z1.5. As discussed IQA updated 3_CYL to 4_CYL in bolero model code.

1. DWVCI2 installation done in T block.

1. DWVCI2 PC was hang and shown no communication with VCI - Issue resolved

For Bolero Neo new model code addition database updated

External DWVCI2 scanning issue solved

External DWVCI2 installed in T block

added EPS does not present model code in the regular database.

1. S block CAI area DL3 print issue solved.

1. DL3 from V block PR issue observed checked and keep in under observation in V block2. S block DWVCI2 setup VCI issue corrected.

1. DL3 1158 Screen issue corrected2. DL3 2212 WIFI card issue solved.3. Printer configured in V block DL3.

DL3-related material checked, sorted and data given to Sunil

New SBRM module added – START COM, CONFIGURATION, Clear code and Option type added in Broadcast decode for Bolero and Bolero NNew service added in Smart core in W6 and Z1New model added in Bolero N and Bolero N+.

The Laptop Gate pass was renewedT-Block offline area 4 DL3 driver updated for Ethernet connectivity and trails taken. - Working Fine. 

1. DL3 2048 Scanner not worked repaired2. DL3 3049 LED not glowing repaired 3. DL3 3029 LED not glowing repaired4. 1 DL3 configured in V block

1. DWVCI-2 setup done in T block

1. DWVCI2 installed in S-block2. Took a trails and it work properly

1. removed the model code from the Bootstrap and Smartcore present section. And added in the IC and IPC section for Z1.

1. 2209 DL3 wifi card changed2. 2045 DL3 wifi card changed

DL3 Issue Analysis and Debugging Support

1. New service added in smart core W6.

1. DWVCI2 setup done in S block 2. 5 Trials took on vehicle level

1. Z1 new model code added in broadcast decode – ESCL2. W6 new service added in HVAC as per below mail

1. HUD config condition corrected on COCKPIT_ECU_FLASHING_STATION2. FRONT_ZONE calibration flashing applicable only for PACK_C vehicle3. A new model was added to the broadcast decode.4. A new W6 model code was added to the broadcast decode

1. DL3 2433 configured2. New model code added in FRM and FCM.3. DoIP Logs checked yesterday found issue in EPS

1. DL3 3050 setup done.

1) Repair station FRM error issue solved.

1. DL3 2212 checked WIFI driver updated2. DL3 2322 still no changed Ultra capcitor mode to battery mode

1. DL3 2212 Reimaged2. DL3 2433 Power mode changed to battery

1. DWVCI2 temporarly issue resolved for DWVCI2 not communicate2. DL3 2211 WIFI card changed

1. DL3 3046 WIFI card changed2. Scanner installed in V block

DWVCI2 bugs fixes in T block

DWVCI2 installed in T block

1. DL3 2246 WIFI card changed.2. DL3 3029 configured

1.DL3 2048 SCANNER ISSUE- I open DL3 and reconnect all cables after it was worked2.DL3 2433 WIFI issue - I disabled driver and enable after it worked

1. DL3 2210 scanner issue solved. Clean Scanner leanse2. DL3 3054 checked on V block.

1. From V block one DL3 reimaged

1. DL3 2048 hard reset done after DL3 woke up

1. 6 DL3 configured from V block2. DL3 2212 checked scanner have issue

1. IPMB RUBBER and VICER collected from MZHLE warehouse

1. DL3 2205 WIFI card changed, DL3 2209 kept under observation to check WIFI card related activity2. DL3 2212 IPMB with Q7 changed some screw are missing need to collect from MAHLE warehouse

1. Laptop gate pass renewed

1. DL3 3047 scanner issue checked. Uninstall and reinstall runtime,2. OFFLINE area cockpit level trail done3. Vehicle level trail done4. DL3 2246 runtime, upload service uninstalled someone. Reinstalled both. DWVCI2 enabled

Regarding DL3 part and DWVCI2 part related discussed with Vikram

1. DL3 2048 Battery pack changed

1. DL3 2432 have printer related issue corrected2. DL3 3031 checked and junk files deleted

1. DL3 2203 battery pack changed

1. DL3 3031 checked, troubleshoot and sorted out issue2. All DL3 checked from S block

1. Printer setting done from DL3 30312. Partially DL3 setup installed in taughbook

1. Docking station checked with Ryan tool 2418, it's shown faulty2. SD card logs need to send

1. Fogbugz updated for docking station and for WIFI card

DL3 2205 partially configured

1. Docking station 2428 Also faulty. checked

1. 3 DL3 configured and tested from V block

1. DL3 2205 WIFI card troubleshoot and replace

1. DL3 2205 tried to reimage but due to some technical issue not reimage properly

1. DL3 2205 WIFI issue checked found older WIFI driver update

1. New service added in W6,2. New model code added in W63. Service verification done in Z1

2205 WIFI card changed and took a trail on line

WIFI card changed DL3 2047

1. DL3 3031 tested and handover to S block team

1. DL3 3031 repaired checked

1. DL3 3031 repaired-Q7 board had issue2. Resident Engg. Invoice submit to Account department

1. DL3 3031 IPMB changed and try to connect KEYBOARD and mouse but same result shown

1. DL3 2045 WIFI card changed2. DL3 3031 IPMB changed due to screw was not available in packet work is hold

1. DL3 3031 IPMB removed and give to Vikram for further RGP process2. DL3 part related required material list sent to sameer

New model code added in VAT for Z1,W6 and Bolero neo

From T block all DL3 observed found issue in DL3 2045, WIFI card have issue

1. DL3 2212 checked Amphanol connector broken,2. DL3 2212 VCI not communicating

1. DL3 3051 have file upload issue solved2. flashing data not push in report logiq server - solved3. MSSNA & MSSI meeting done4. Reading DoiP documents

1. DL3 3031 checked as per jim instruction but there is issue in IPMB need to check internally2. DL3 network issue in V block checked with MAHINDRA IT person

1. HPC AD changed in DoIP database2. DL3 SD card files pasted as per JIM instruction but still DL3 not work

1. Took trail on M310 and W610 with new VAT binary, logs checked working fine2. Worked on DWVCI2. Dead to Live3. Laptop gate pass renewal process done.

1. DL3 3048 Q7 board changed.2. One new Q7 board bring from MAHLE office

1. DL3 2208 WIFI card changed2. DL3 3031 VCI troubleshoot and checked, VCI have issue3. DL3 2212 have Q7 board issue

1. OFFLINE JIG level trail taken2. W6 New model code added in VAT database3. DL3 2209 checked for slow running issue - SSD memory was full4. DL3 2211 flashing not happened checked and solved - HEX file was corrupted

1. Prepared part list under warranty replacement2. Regarding gate pass renewal documents checked with Ajay sir, and informed to internal team

1. DL3 2203 - occurred runtime error. Checked - Someone changed their date format because a runtime issue occurred2. Tried to take the trail on SRS module over offline zig but offline zig has some issues. So today we can't take a trail on the SRS module

1. DL3 2212 battery changed2. DL3 2203 OBD connected to Y splitter, error shown in DTC tool - Checked3. SKU error handled of bajaj

1. DL3 2212 network issue, the firewall was on because it losing connectivity2. ATP list updated for CANFD protocol.

1. DL3 2300 checked their WIFI connectivity, partially solved2. 4 OBD cables were delivered to MAHINDRA. For 2 T block with the new connector and for 2 V block for DoIP support3. DL3 2208 has a Wi-Fi card issue that needs to replaced under warranty.4. DL3 2246 checked and updated handover an line.

1. DL3 2208 and DL3 2047 have vci and network related issue solved

1. 1158 DL3 WIFI card changed,2. 2203 DL3 Q7 board changed3. DL3 3048 Q7 board damaged FB raised, 2203 DL3 Q7 board gone fogbugz raised,4. Mail sent to M&M S block team,

1. For bolero neo info deleted from one model2. W6 MBFM service checked3. Z1 new model added in VAT database line item mentioned in vat tracker

DL3 SN 3047 amber LED blinking, told to keep till battery drain after try to boot up

1. DL3 1158 had WIFI card related issue. I disconnected and connected same WIFI card and keep under observation

1. DL3 2209 WIFI card replaced at T block2. Front zone module flash log sent to tushar3. BAJAJ database handover to yash4. DL3 2300 WIFI card changed at S block5. DL3 2203 Q7 board changed at S block6. New DL3 without domain, again we took trail on zig level and vehicle level to check behaviour of DL37. taking New VIN MODEL scanning trails8. ABS type changed for Line item 78 to 81 for bolero neo

1. S block and T block DL3 checked 2. DL3 2047 and DL3 2208 issue solvedDL3 2047- ECATS 6000 issue foundDL3 2208 - WIFI card related issue found - Network drivers uninstall and resinstall

1. New model addition for W6

1. S block all DL3 checked.2. T block all DL3 checked.

1. S block offline area all DL3 printer enabled, PRN file updated as per requirement,2. DL3 3051 configured with V block credentials

1. DL3 2300 checked ethernet connectivty, due to security reason blocked port. Sent mail to MAHINDRA IT team,2. DL3 1158 checked, issue: Not bootup- After restart DL3 1158 bootup and working fine3. DL3 3030 checked OBD cable issue. Power cable soldering is broken because vehicle communication not happened, told reason to MAHINDRA maintainance team to solder properly on power cable4. DL3 3051 configured for V block

New Model added for RVC in W6 database

1. New security added in database version 5.6.41.152. 2 new serviecs added in database, Option type and new condition created for ABS module bolero3. Same changes done in database 5.6.41.164. VATBIN tracker updated and sent to MAHINDRA team

1. Docking station issue solved2. New service added in bolero neo3. DL3 2046 battery board checked, no issue found

1. Gate pass renewal procedure done

1. DOIP initial level trail taken sent log to tushar2. DL3 3051 LAN port installed, taken in MAHINDRA domain but due to IP address not available. Still New account and admin rights not given to DL3

1. Fitness certificate taken from hospital2. Due to change safty policy required different fitness certificate - Gate pass renewal procedure still pending

1. Compliance procedure completed,2. Safty and security procedure pending(Fitness certificate expired),3. Laptop gatepass renewed,4. Try to get new DL3 in MAHINDRA domain but because LAN port issue today DL3 configuration not happened

DOIP first trail taken

1. 2300 DL3 have WIFI card issue, LAN ports driver installed and connected through LAN and external scanner2. New OBD cable given for testing

1. W6, Z1 and TUV services added in version 5.6.41.13 and 5.6.41.14

1. 2205 Q7 board changed

DL3 2205 WIFI card changed

1. DL3 2300 scanning not happened as well as station not change issue occured - Solved2. TPMS service report created sent to mallamma3. RVS and RVS2 station condition updated for 11 digit export sku

1. DL3 1158 Q7 board changed2. DL3 2212 Configured, taken trails3. DL3 2246 Configured, taken trails4. New docking station checked USB port not working image sent on MAHLE whats group

1. DL3 2211 configured2.DL3 2048 WIFI card changed3. DL3 2212 SSD card changed4. DL3 2212 OS restored5. DL3 2246 OS restored6.DL3 2212 & DL3 2246 Configuration pending7. DL3 1158 Q7 board replacement pending8. TVS BMW database, updated condition in RVC station9. PID list updated for side stand test

1. Delivered 2 new OBD cables, 3 SSD card, 1 WIFI card and 1 Q7 board2. DL3 2211 - Changed SSD card3. DL3 2211 - Restored OS image, given to mahindra IT team4. DL3 2211 - Configuration is pending5. U400 - Side stand test updated from time base to signal base, given binary to mallamma to taking trail

1. Old DL3 image downloaded and restored

1. Disabled RPAS test in final flashing API and repair flashing API for bolero longer

1. Old DL3 OS downloaded as per given instruction from JIM

1. New image tried to restore on old DL32. New image not restored on old DL3 because 256 SSD card image not supported to 128 GB SSD card

1. Meeting schedule with MAHINDRA block persons

1. New Image copied from New DL32. DL3 image kept on backup

1. DL3 2208 have scanning and WIFI driver issue2. Troubleshoot issue3. Restore image 4. Due to MAHINDRA IT policy drivers are uninstalled

1. DL3 3030 VCI communication issue2. Checked static IP, Internal Ethernet LED is working or not3. Not found root cause DL3 3030 keep in under observation

1. DL3 2210 configured2. Restored image in DL3 2210

1. DL3 2210 scanning not happened2. So troubleshoot issue 3. Checked drivers4. Checked TRA file5. Issue from MAHINDRA IT side API was blocked

1. All DL3 checked from T block2. DL3 3031 have API blockage issue solve from MAHINDRA IT side3. 2205 DL3 have WIFI driver issue, restored image

1. All DL3 checked from S block 2. DL3 2202 external scanner implementation3. DL3 2208 restore image

1. DL3 2211 checked they have SSD card issue2. DL3 2246 Reimage

1.2211 DL3 not bootable - SSD card removed and inserted2. 3048 DL3 VCI communication issue- Restarted and its working fine3. Need to find out root cause 3048

1. 3048 DL3 configured2. 2431 and 2432 DL3 bring from MAHINDRA

1. 10 DL3 delivered2. 5 OBD cable delivered3. 1158 DL3 checked Q7 board issue4. CAI S block DL3 WIFI card issue5. DL3 3031 configured and delivered

1. DL3 2211 hang issue solved2. 3046 DL3 configured

1. DL3 2208 IPMB, Q7 and front button panel changed2. DL3 tested and working fine

1. Today i found DL3 buttons are not working,2. Q7 board also damaged, tomorrow will replaced

1. DL3 2208 IPMB changed but still not booting up BU msg shown in 7 segment LED2. Need to check on wednesday

1. In ICC New service added for W6 and Z1

1. DL3 2212 checked to reimage but there SSD card have issue in S block2. DL3 3030 configured for T block3. DL3 2208 bring in MAHLE office for IPMB check and replace

1. 2 services sending NRC, PBF checked conclude issue2. DL3 2211 delivered in mahindra3. DL3 2211 updated hex files, binary and PLANT file

1. In Pendrive DL3 image creation done

1. DL3 Image creation not happening in pendrive it was stuck at 92%

1. DL3 2212 showing shell error on black screen not start- Need to required reimage there SSD card not showin on setup screen. Due Pendrive issue can't reimage today2. Checked PBF file for bajaj can't found issue from our side

1. DWVCI2 bring from mahindra2. Regarding new DL3 delivered recived copy not meet from Sagar so discussed with them with Manesh, sameer and tushar

1. 2208 DL3 checked scanner related issue as discussed with IT team keep on under observation in T block2. 4 New DL3 delivered and got recived recipt from 3 DL3 & 1 is pending

1. Root cause analysis of DL3 2208, Why scanner not work after some vehicles2. Root cause found in trace. Mail sent to Mahindra team3. Regarding MY23 signoff, sent mail to Vikas. 

1. DL3 2246 reimage procedure completed2. DL3 2208 scanner issue temporarly solved

1. DL3 2211 changed DL3 display and WIFI card

1. DL3 1158 repaired2. 2 repaired docking station, DL3 2246 and DL3 1158 delivered to MAHINDRA3. 2 Battery board as a spare part delivered to MAHINDRA4. DL3 2208, DL3 1158 and DL3 2246 scanner issue resolved5. DL3 2211 Battery board replaced6. For display broken DL3 2211 bring in MAHLE office

1. DL3 1158 Screen cable and LED cable changed but still DL3 not wake up. Screen cable is loose need to fit properly

1. DWVCI 2 testing and validation in T block

1. DWVCI2 installation remotely support to T block

1. 10 New OBD cables and 1 repair OBD cable delivered to T block MAHINDRA2. DL3 2211 reimaged3. DWVCI2 setup installed in T block PC testing is pending

1. SN 1158 from mahindra bring DL3 in mahle office

1. T block scanning not happenening with DL3 2208. Checked and solve issue2. S block DL3 2431 reimage and configuration done3. 1158 DL3 checked there internal screen ribbon cable is broken need to replace 

1. Broadcast decode cross verified models of Z1, 2. Broadcast decode cross verified models of W6,3. Broadcast decode cross verified models of Bolero Neo

1. DL3 2431 configuration 2. OS have different so need to reimage DL3

1. Broadcast decode changed for Scorpio N and XUV 7002. VAT database updated and sent to EOL time for testing and validation.

1. DL3 2432 delivered to T block2. DL3 2211 WIFI card changed. Keep in observation

1. Replaced Q7 board after DL3 2432 working fine

1.       All DL3 checked in T block.2. External scanner implement in DL3 2211 but due OBD cable have not enough pins, i suggest them to add internal cables in OBD cable like DL3 OBD cable

DWVCI 2 DEMO meeting1. Regarding DWVCI2 meeting done with Sagar choudhari2. New OBD cable requirement sent to manesh sir

1. One service sending NRC, i checked and sent mail to vikas for correction2. 2205 DL3 have issue but after found root cause, there is IP issue3. 2045 DL3 i reimage and WIFI card i reinstall and changed IP after its working fine

1. For T block DL3 related support remotely provided to T block printer configuration, 2. network related issue[IP issue], 3. VCI communication issue

Repair flashing API station there added new pre flash commands for validation sent binary file

1. DL3 2210 WIFI card changed, driver issue need to solved2. DL3 2432 scanner issue, due to dust it was not scan. After clean scanner its working fine3. DL3 2045 WIFI card issue after replaced WIFI card it's working fine

1. New DL3 delivered in MAHINDRA2. DL3 configured3. Testing and validated

1. DL3 IPMB changed2. Battery board changed3. Testing and validation in warehouse